ddx – read user manual online or download in PDF format. Pages in total: 12 . This page contains information about the User Manual for the DDX from Behringer. Music Mixer Behringer ddx different pdf manuals and documents on this page.
|Published (Last):||7 April 2008|
|PDF File Size:||7.80 Mb|
|ePub File Size:||14.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
To reduce the risk of electric shock, do not remove the cover or rear. No user serviceable parts inside; refer dds3216 to qualified personnel. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure—voltage that may be sufficient to It is one of my most pleasant tasks to write this letter to you, Ex factory, the analog inputs are assigned to channels It complies with all applicable behrinfer standards.
Blown fuses must always be behrjnger by fuses of the same type and rating. Channel level meter Each fader has a channel level meter assigned to it. Depending on the active fader bank, this meter reads the pre-fader or pre- processing levels inputsor the post-fader output level outputs such as bus, aux and FX.
Normally, the channel meter follows the fader bank settings and reads the level of its associated fader. Display with control elements Many functions of your mixing console are controlled via the display, including the general setup, channel processing mznual the built-in effects processors.
By pressing a switch in the switch block, you can display whole groups of associated menu pages. Each group has a menu bar on the upper right side, and each single menu page has a tab along the top left part of the display. Groups can manuxl more than one fader menu page. The low-cut filter has only one frequency parameter, which controls the frequency at which the signal is cut by 3 dB cutoff mnual.
Behringer DDX User Manual | 12 pages
All frequencies below that value are attenuated with a slope of 12 dB per octave. So, when you select a frequency of Hz, it will be cut by 3 dB; The lower the threshold, the more the signal is affected. Signals below the threshold, however, remain unaffected.
These busses can be used for a wide variety of applications, e. The aux and FX sends are adjusted with the channel controllers and the display. Using the AUX and FX switches in the left switch block you can assign one common aux or FX send to the channel controllers of channels or When you press the AUX and FX switches in the left switch block, the AUX and FX send page is displayed, providing you with an overview of all sends and masters, including their pre and post-fader settings.
These four multi-effects processors offer 26 different groups of first-class effects, including such standard effects as reverb, chorus or delay, but also unconventional effects such as a ring modulator, plus various filter and lo-fi effects. Decay 0 to 10 s The Decay parameter controls the duration of the reverb tail, which is the time needed for the level of the reverb tail to drop to dB. PreDelay 0 to ms This parameter controls the delay in msuntil early reflections and reverb tail can be heard.
Diffusion 0 to 20 The Diffusion parameter allows you to edit the density of the reverb tail. Size 1 to 50 Size determines the room size with regard to the early reflections. The signal is also fed back. The resulting phase shift is called comb filter effect. Mod Delay 5 to ms Mod Delay controls the delay of the modulated signal. NR-Response 20 to ms This parameter controls the response time of the gate.
Any changes made here will be stored until you power off your DDX or change them next time you use the copy function. The inputs are assigned in blocks of eight, which enhances the flexibility of your DDX considerably. This input is fitted with a sample rate converter that allows you to feed in digital signals with sample rates between 32 and 50 kHz.
What is more, your DDX stores the last snapshot used and recalls it after power-up.
These files can be used as backups or to transfer data from one DDX to another. Copying a file of this type to the middle window internal files will delete all DDX settings, and load a new operating system see chapter Snapshots can also be switched over by means of program change commands see chapter Simply start the multi-track recorder and mix, and the DDX will play back exactly what has been recorded before, or will record what is being added. If the switch is disabled, the DDX is in absolute mode, i.
The flash memory of the console stores one automation file. Adjustments can always be made later on, but the mixer will use the status of the controls as the basis for the new mix when automation is turned on.
The built-in clock of your DDX Check the appropriate checkboxes to enable these functions. Any additional DTRS wordclock code via the sync port of the master recorder, and are configured as slaves. The packaging of your DDX contains two 19″ rack mounts for installation on the side panels of the console.
Before you amnual attach the rack mounts to the DDX, you need to remove the screws holding the left and right side panels. However, you can also use two-conductor shielded cables e.
As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
Music Mixer Behringer ddx3216 user’s manuals in pdf
Page of 56 Go. Table of Contents Add to my manuals Add. Ultimate 5-channel digital dj mixer with sampler, 4 fx sections, dual bpm counters and midi 30 pages. Ultimate 5-channel digital dj mixer with sampler, 4 fx sections, dual bpm counters and midi 21 pages.
Professional 5-channel dj mixer with advanced digital effects and bpm counter 10 pages. Professional 5-channel dj mixer with advanced digital effects and bwhringer counter 11 pages. Professional dj mixer with a total of 10 stereo sources on 5 dual-input maual 29 pages. Professional dj mixer with a total of 10 stereo sources on 5 dual-input channels 22 pages. Professional dj mixer with a total of 4 stereo sources on 2 dual-input channels 19 pages. Table Of Contents 1.
Introduction Seeing is believing! Main Mix Channel level meter Each fader brhringer a channel level meter assigned to it. Channel Control Bank Groups can span more than one fader menu page.
Behringer DDX3216 Musical Instrument User Manual
Auto mation Bank 2. Channel Processing Switches 6 dB cuts the amplitude by half. Dynamics Processing The low-cut filter has only one frequency parameter, which controls the frequency at which the signal is cut by 3 dB cutoff frequency. Dynamics Library Menu Page The lower the threshold, the more the signal is affected. Page 23 The aux and FX sends are adjusted with the channel controllers and the display.
Small Hall Decay 0 to 10 s The Decay parameter controls the duration of the reverb tail, which is the time needed for the manusl of the reverb tail to drop to dB. Phaser LFO Speed 0.
Groups, Pairs And Copy Functions 7. Pair Function turn to select; press to change. File Management What is more, your DDX stores the last snapshot used and recalls it after power-up. Dynamic Automation Simply start the multi-track recorder and mix, and the DDX will play back exactly what has been recorded cdx3216, or will record what is being added.
Perfecting A Mix Adjustments can always be made later on, but the mixer will use the status of the controls as the basis for the new mix when automation is turned on. Setup 32 and 50 kHz, regardless of whether or not these signals drx3216 in sync with the console.
The Ddx In Live Applications including equalization and effects with the faders of channels Installation The packaging of your DDX contains two 19″ rack mounts for installation on the side panels of the console.
Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it.
Don’t show me this message again. Got it, continue to print. Don’t have an account?