HIN232 DATASHEET PDF

HIN Datasheet PDF Download – +5V Powered RS Transmitters/ Receivers, HIN data sheet. HIN datasheet, HIN circuit, HIN data sheet: INTERSIL – +5V Powered RS Transmitters/Receivers,alldatasheet, datasheet, Datasheet search site. HIN from Harris Corporation. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Malaran Negar
Country: Ukraine
Language: English (Spanish)
Genre: Automotive
Published (Last): 16 March 2012
Pages: 76
PDF File Size: 13.53 Mb
ePub File Size: 1.98 Mb
ISBN: 559-6-15861-734-9
Downloads: 93856
Price: Free* [*Free Regsitration Required]
Uploader: Naktilar

They require a single V power supply except HIN and feature onboard charge pump voltage converters which generate V and -V supplies from the V supply. The receivers also feature hysteresis to greatly improve noise rejection. These devices are sensitive to electrostatic discharge; follow proper Datxsheet Handling Procedures.

HIN232 Datasheet

All other trademarks mentioned are the property of their respective owners. Internally generated negative supply -V nominal. C External capacitor terminal is connected to this lead. C- External capacitor – terminal is hin23 to this lead. An internal 00k pull-up resistor to is connected to each lead. These inputs accept RS- input levels. An internal pull-down resistor to GND is connected to each input.

This is an active low input which enables the receiver outputs. No connections are made to these leads. Please refer to TB for details on reel specifications. They are not intended for use in Reflow solder processing applications.

HIN datasheet, Pinout ,application circuits +5V Powered RS Transmitters/Receivers

Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB for details. Electrical Specifications Test Conditions: Limits established by characterization and are not production tested.

Temperature limits established by characterization and are not production tested. The circuit is divided into three sections: The charge pump, transmitter, and receiver. Charge Pump An equivalent circuit of the charge pump is illustrated in Figure.

The charge pump contains two sections: Each section is driven by a two-phase, internally generated clock to generate V and -V. The nominal clock frequency is khz.

During phase one of the clock, capacitor C is charged to. During phase two, the voltage on C is added to, producing a signal across C equal to twice. During phase one, C is also charged to, and then during phase two, it is inverted with respect to ground to produce a signal across C equal to. The charge pump accepts input voltages up to.

The output impedance of the voltage doubler section V is approximately 00, and the output impedance of the voltage inverter section is approximately 0. Increasing the values of C and C will lower the output impedance of the voltage doubler and inverter, increasing the values of the reservoir capacitors, C and C, lowers the ripple on the V and supplies.

  DISPERSI KOLOIDAL DAN SIFAT-SIFATNYA PDF

The transmitter outputs are disabled and the receiver outputs are placed in the high impedance state. A logic at the input results in a voltage of between -V and at the output, and a logic 0 results in a voltage between V and V Each transmitter input has an internal 00k pullup resistor so any unused input can be left unconnected and its output remains in its low state. V, and maximum allowable operating temperature. The outputs are short circuit protected and can be shorted to ground indefinitely.

The receivers have a typical input threshold of. The receiver output is 0V to. The output will be low whenever the input is greater than. The receivers feature 0. V hysteresis to improve noise rejection. The receiver outputs are also placed in the high impedance state when in shutdown mode.

It is particularly useful hn232 applications where V power supplies are not available for conventional RS- interface circuits.

The applications presented represent typical interface configurations. Fixed output signals such as DTR data terminal ready and DSRS data signaling rate select is generated by driving them through a resistor connected to V. In applications requiring four RS- inputs and outputs Figurenote that each circuit requires two charge pump capacitors C and C but can share common reservoir capacitors C and C.

The benefit of sharing common reservoir capacitors is eatasheet elimination of two capacitors and the reduction of the charge pump source impedance which effectively increases the output swing of the transmitters.

Please go to the web to make sure that you have the latest revision. Added Rev History beginning with Rev. Updated to new POD standard by removing table listing dimensions and putting dimensions on drawing. Added land pattern About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The hni232 products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.

For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at You may report errors or suggestions for improving this datasheet by visiting Reliability reports are also available from our website at FN.

In case of conflict between English and Metric dimensions, the inch dimensions control. D, D, and E dimensions do not datassheet mold flash or uin232. Mold flash or protrusions shall not exceed 0. E and e A are measured with the leads constrained to be perpendicular to datum -C B maximum dimensions do not include dambar protrusions.

  KSAN CHARTS PDF

Dambar protrusions shall not exceed 0. N is the maximum number of terminal positions. Dimension D does not include mold flash, protrusions or gate burrs.

Mold flash, protrusion and gate burrs shall not exceed 0. Dimension E does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0. Hin2322 chamfer vatasheet the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. L is the length of terminal for soldering to a substrate.

N is the number of terminal positions. Terminal numbers are shown for reference only. The lead hin23 B, as measured 0. Converted inch dimensions are not necessarily exact. Package length does not include mold flash, protrusions or gate burrs. Package width does not include interlead flash or protrusions. The lead width as measured 0. Converted inch dimensions in are not necessarily exact. Dimension B does not include dambar protrusion. Allowable dambar protrusion shall be 0.

Converted inch dimensions are not necessarily exact. Dimensions D and E to be determined at seating plane -C Dimensions D and E to be determined at datum plane -H Dimensions D and E do not include mold protrusion. Allowable protrusion is 0. Dimension b does not include dambar protrusion.

N is the number of terminal positions. Intersil Corporation s quality certifications can be viewed at Datasheeg products are sold by description only. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.

Information furnished by Intersil is believed to be accurate and datashfet. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor datzsheet any infringements of patents or other rights of third parties which may result from its use.

No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see FN.

This classification indicates that the product is obsolete and notice has been given. Sale of this device is currently. Two regulated current ports are designed.

HIN datasheet, Pinout ,application circuits +5V Powered RS Transmitters/Receivers

The DM74LS selects one-of-eight data sources. It provides, in one package, the ability to select one bit of data from up to eight sources.

The LS can be used as hinn232 universal function. Designed to operate from.