Thermaroof TR26 is designed for flat roof insulation with mechanically fixed single-ply waterproofing. Download the specification here. INSULATION FOR FLAT ROOFS WATERPROOFED WITH. MECHANICALLY FIXED SINGLE-PLY WATERPROOFING. Seventh Issue. October TR26 LPC/. These examples are based on Kingspan Thermaroof® TR LPC/FM, waterproofed using a mechanically fixed single–ply membrane. The insulation board is.
|Published (Last):||5 December 2016|
|PDF File Size:||11.87 Mb|
|ePub File Size:||10.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Unfortunately, further to the recent supply challenges with PIR and Phenolic insulation boards from Celotex, Kingspan, Ecotherm and Recticel, available stock of these product will vary throughout the country.
We will endeavour to source the required stock, however, we may need to mix and match equivalent products from multiple manufactures, suppliers and depots. This may affect the rates; we will of course discuss possible solutions with you before proceeding and will do our best to keep additional costs down. Specialised insulation boards will be affected more than general application boards, so please allow additional time to process and deliver these orders.
Please allow extended lead times on PIR and Phenolic foam insulation.
The most popular board sizes may be available from stock. This Thermaroof Range includes the following readily available product thicknesses 25mm, 40mm, 50mm, 60mm, 70mm, 80mm, 90mm, mm, mm, mm, mm and mm. Manufactured to order are the following thicknesses 30mm, 45mm, 55mm, 65mm, 75mm, 85mm, 95mm, kingspaj, mm, mm, mm and mm. Insulation for flat roofs waterproofed with partially bonded kingspxn applied multi—layer bituminous waterproofing.
ThermaRoof TR26 is a foil faced insulation for flat roofs with mechanically fixed single-ply waterproofing.
Select products below to see pricing structure Use product tick-boxes to select required products Add to Basket Kingspan TR26 25mm, 12 x 1. Kingspan TR26 40mm, 8 x 1. Kingspan TR26 50mm, 6 x 1. Kingspan TR26 60mm, 5 x 1. Kingspan TR26 70mm, 4 x 1. Kingspan TR26 80mm, 4 x 1. Kingspan TR26 90mm, 3 x 1.
Kingspan TR26 mm, 3 x 1. Kingspan TR26 mm, 2 x 1. Presently there are no availability restrictions, apart from manufacturing lead-times and minimum quantity order levels on certain product sizes. Please observe the ‘Star Rating’ indicators to assess availability.
Kingspan Thermaroof TR26 is faced on both sides with a low emissivity composite foil, autohesively bonded to the insulation core during manufacture. Determination of compression behaviour. TR26 should always be installed over a vapour control layer or sealed metal deck. If correctly applied, the TR26 Boards have an indefinite life.
Its durability depends on the supporting structure and the conditions of its use. The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils.
However, it is recommended that any spills be cleaned off fully before the boards are installed. Ensure that safe methods of cleaning are used, as recommended by the suppliers of the spilt liquid. The insulation core is not resistant to some solvent—based adhesives systems, particularly those containing methyl ethyl ketone.
Adhesives containing such solvents should not be used in association with this product. Tf26 boards or boards that have been in contact with harsh solvents or acids should not be used. The insulation core and facings used in the manufacture mingspan TR26 resist attack by mould and microbial growth, and do not provide any food value to vermin. TR26, when subjected to the British Standard fire test specified in the table below, will achieve the result shown, when waterproofed with a single-ply waterproofing membrane.
Result Dependent on single-ply membrane adopted Further details on the fire performance of Kingspan Insulation products may be obtained from the Kingspan Insulation Technical Service Department see below. High performance rigid thermoset insulation – thermal conductivity 0. Part 1 FM approved for Class 1 steel deck roof assemblies Fully compatible with most mechanically fixed single-ply waterproofing systems Compatible with most green roof systems Installation technique is ideal for fast track building programmes Resistant to the passage of water vapour Easy to handle and install Ideal for new build and refurbishment Non-deleterious material Manufactured with a blowing agent that has zero ODP and low GWP.
Click to download in a separate browser window. Fibre free, rigid insulation used for flat roofs that is compatible with the majority kingspah torch applied waterproofing system. Glass tissue faced insulation for fully adhered single-ply, partially bonded built-up felt, mastic asphalt waterproofing. Structural insulation faced with plywood composite for flat roofs waterproofed with partially bonded built—up felt.
Kingspan Thermataper TT46 comes with a supporting design service. This ensures that the most cost-effective solution for kinsgpan roof is identified and that the end result is a tapered system design which meets a roof’s rainwater run-off and insulation requirements. Further details of Kingspan Thermataper TT46 are available from the Kingspan Insulation Tapered Roofing Department see rear coverwhich should be consulted as early as possible in the process of designing a roof.
TR26 is suitable for use with most mechanically fixed single-ply waterproofing membranes. Kingspan Thermaroof TR26 Is not suitable for use with bitumen based built-up waterproofing systems or mastic asphalt. TR26 should be installed over a separate vapour control layer, in new build roofs, unless it is being used in conjunction with a sealed metal deck.
Regardless of the deck type it is recommended that a condensation risk analysis is carried out for every project. For refurbishment projects, involving the addition of insulation to existing insulated flat roofs, or roofs constructed of insulated steel faced composite panels, it is imperative that a U Value calculation ,ingspan condensation risk analysis is carried out for every project, in order to ensure that the correct thickness of insulation is installed to achieve the required thermal performance, whilst avoiding interstitial condensation.
Therma TR26 FM Roof Board
In refurbishment projects, where TR26 is to be installed over an existing bituminous waterproofing membrane, the membrane can be used as a vapour control layer, as long as it is in a good water tight condition. Where this is not the case, a separate vapour control layer should be installed. A minimum separate vapour control layer should consist of a gauge micron polythene sheet, with all joints lapped and then sealed with double sided self adhesive tape.
TR26 is suitable for use on access roof decks subject to limited foot traffic. Where inappropriate foot traffic is liable to occur it is recommended that hr26 roof surface is protected by specially constructed walk-ways.
For further advice on the acceptability of specific foot traffic regimes, please contact the Kingspan Insulation Technical Service Department see rear cover. TR26 is suitable for use under most green roof systems. Green roof systems are a specialist design area. When designing a loose-laid insulated green roof assembly consideration needs to be given to the following. However, the total required dry weight will depend upon wind uplift, which in turn will vary with the geographical location of the building, local topography, and the height and width of the roof concerned.
The necessity for any additional dry weight should be assessed in accordance with BS EN -1 When installing a loose-laid insulated green roof assembly, any insulation must be immediately over-laid with the green roof system, which must meet all of the requirements outlined above.
Where these requirements cannot be ensured, the insulation must be mechanically fixed. For further information please contact the Kingspan Insulation Technical Service Department see below.
Metal decks should be clean, dry, without large projections, steps or gaps, and should be graded to allow correct falls to all rainwater outlets. Where one run of the specified vapour control layer laps another, there kingspab be minimum mm side and end overlaps, which should be adequately sealed. Turn up the vapour control layer at kingspna edge of the roof to a height appropriate to the specified waterproofing membrane.
Kingspan TR26 for Single Ply Waterproofing Flat Roofs
Boards of TR26 should be secured to the deck using mechanical fixings e. Insulation boards should always be laid break-bonded, either with their long edges at right angles to the trough openings, or diagonally across the corrugation line, and with joints lightly butted. There should be no gaps at abutments. Roof-light or ventilator kerbs etc. A 25 mm thick TR26 upstand should kkingspan used around the perimeter of fr26 roof on the internal fagade of parapets. A minimum distance of mm should be maintained between the top of the insulation upstand and the bottom of the horizontal roof insulation.
Thermaroof TR26 LPC/FM | Insulation | Kingspan | MEA & India
The waterproofing membrane is also mechanically fixed in accordance with the membrane manufacturer’s instructions, over the whole insulated area including any insulation upstands, as soon as possible after laying the insulation boards. Kingsapn decks should be clean, dry, without large projections, steps or gaps, and should be graded to allow correct falls to all rainwater outlets.
Insulation boards should always be laid break-bonded, either with their long edges at right angles to the edge of, or diagonally across the roof, and with joints lightly butted. Order before 10am for next working day delivery. Subject to product availability locally, and vehicle delivery slots.
Product Characteristics The Facings Kingspan Thermaroof TR26 is faced on both sides with a low emissivity composite foil, autohesively bonded to the insulation core during manufacture. Kingspan TR24 Fibre free, rigid insulation used for flat roofs that is compatible with the majority of torch applied waterproofing system Click for more information Kingspan Kingspsn Glass tissue faced insulation for fully adhered single-ply, partially bonded built-up felt, mastic asphalt waterproofing.
Click for more information Kingspan TR31 Structural insulation faced with plywood composite for flat roofs waterproofed with partially bonded built—up felt Click for more information Celotex TD Celotex Tempchek Deck TD Range is PIR insulation bonded to plywood for, use in fr26 flat roof applications.
Click for more information. Roof Waterproofing TR26 is suitable for use with most mechanically fixed single-ply waterproofing membranes. Water Vapour Control TR26 should be installed over a separate vapour control layer, in new build roofs, unless it is being used in conjunction with a kigspan metal deck.
Green Roofs TR26 is suitable for use under most green roof systems. If using a sealed metal deck there is no requirement for a separate vapour control layer. If the metal deck is not sealed the vapour control layer should be loose-laid. Installing over Concrete Decks Concrete decks should be clean, dry, without large projections, steps or gaps, and should be graded to allow correct falls to all rainwater outlets.
The vapour control layer should be loose-laid over the deck.